Plumbing 101: Tips for Bathtub Installation
Plumbing 101: Tips for Bathtub Installation
Blog Article
What are your thoughts about Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't exactly brain surgery, yet it does need solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is easily accessible, the task can move speedily; if you need to open up a wall to get rid of the old tub and also position the brand-new bathtub, the task is much harder. In either situation, the task is within a house handyman's abilities, although you will certainly need an assistant to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed job, it is much better to think about utilizing one prior to you begin. Possibilities are you may need an expert plumber to make tube links.
This short article will certainly aid you install a new tub in your washroom if you have already purchased a brand-new bathtub and also do not require to transform the arrangement of your previous supply of water pipes.
Your tools as well as material checklist ought to make up the following:
Getting ready for the Setup
To start with, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its last placement.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the water system. After doing so, activate the taps to drain any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome due to the restricted gain access to that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. When the supply pipelines have been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Setting up the Bath tub
Using both wooden boards under its feet, position the bathtub in the needed placement. The wood boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as adjusting the feet on the bath tub until the level reads level.
To mount taps, fit the bottom of the outermost flexible tap port to the proper supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the water system and examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as also inspect the overflow outlet as well as the regular outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bath tub has been utilized at the very least when as this will certainly resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, then you will require lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin making certain that the washers are in area in between the faucet as well as the sink. Secure the faucet in place with the producer provided backnut. When the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The previous kind should be linked to the tap ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to crack an inflexible seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, causing issues with wetness and possible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break relatively early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue and also cement.
Bathtub Installation
How Important Is A Bathtub To Your Home?
High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.
Install Piping Before Tub
You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.
Position the Tub
Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.
NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.
Assemble Drain Connections
Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.
Place a Pipe For the Shower Head
First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.
Attaching Hot and Cold Water Lines
Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.
Install the Spout
Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.
NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.
Check For Leaks
Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.
estore the Bathroom Wall
Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.
https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/
I'm very curious about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you enjoyed reading our piece. Sharing is caring. You just don't know, you might be doing someone a favor. We truly appreciate reading our article about Tools You Need to Install a New Bathtub .
Immediate plumbing assistance for emergencies. Report this page